Title : Irwin Industrial Tools 3061001 Miter Saw Laser GuideDescription : Convert your miter saw into a precision laser-guided power tool! Simple to install, just replace the saws outside blade washer with the self-aligning Laser Guide. The guide projects a clear line just to the left of the cut, and turns on and off automatically at 400RPM. No more "sneaking up" on a mark, just cut on the line. Will not fit Bosch, Rigid, ProTech, or DeWalt model 704 or 705 saws. Includes: Laser guide and batteries. Three different installation bolts to cover most applications. Hex key for battery installation. Soft sided storage caseThe Irwin Miter Saw Laser Guide fits onto most miter saws to create a laser-guided power tool. The guide projects a line just to the left of the cut to enable precise cuts and includes two batteries with a 1.5-hour life and extra-long bolts to secure the guide to your saw. It automatically turns on and off as the saw blade starts and stops rotating.
With so many on offer these days, it is great to have a name you can trust. This item is certainly that and will be a perfect buy. The distributor have added some great touches and this equals great value.
You can trust this review, i hope you can try to buy this product and then you know this product good or no. Next time you can make a review
for another people.
1st Customer Review : This laser guide worked for me!
Some of the other reviews didnt mention that in the description of this product, that it does clearly state that it "fits MOST Miter Saws, Does Not Fit The Bosch, Ridgid & Pro-Tech Model Miter Saws". I have a Dewalt DW715 12" compound miter saw, and after READING the instructions, installed it in just a few minutes. I then marked a scrap piece of wood with a thin pencil line from a .5mm mechanical pencil, turned the saw on, lowered the blade slightly and the laser line appeared. The laser is thin and clean. Because it is mounted next to the blade and does not activate until the the blade is turning, you cannot see the laser until you begin to lower the blade slightly and the blade cover moves out of the way. I placed the laser dead on with the line on the wood and it cut dead against it to the left as advertised. It is not meant to cut dead on the line. Again, others posting reviews did not read the product description where it does clearly state "Projects A Clear Line Just To The...
Click here to read the full review for more information about this product.
2nd Customer Review : Works perfectly for me.
D. Steele said all that needed to be said below. Excellent product that works extremely well. I've used this laser on my DeWalt 705 to trim out two houses over the past month or so and I am very pleased. It projects a crisp line just a fraction of a milimeter to the left of the cut. If you're not getting accurate cuts, it's your saw setup, not the laser at fault. I'm buying 2 more for other saws. The only way to improve this product would be to have a system where the laser was projected on both sides to show kerf, but that would require a whole different system and likely a saw specific(read expensive) design.
3rd Customer Review : Works Great
I saw this product in a display, came to Amazon and read a less than great review, causing concerns. I e-mailed the company and explained that I have a DW 705 12" miter saw and wondered if the product would work with that saw. The reply was that it would work with their "kit". I was asked for my mailing address so the kit could be sent. Well, today (9/07/05)the kit arrived. So, I bought the product, went to my shop, and installed the unit w/o the kit, first (it must be a guy thing). To my suprise, I found the unit to have an inset for the arbor (on the blade side) and the factory bolt worked just fine, no observed need for the kit. I reinstalled the blade guard and checked for clearance. All was fine. I started the saw and found no problems. I turned every lite on in my shop and found I see the line without any trouble whatsoever. I have 2 four foot double bulb lights right at my miter saw. I read the paperwork for the kit and find that it is for "older" 705 saws.
Long...
Product Features :
- Retro-Fit your miter saw into a laser guided power tool
- Projects a laser guide line for accurate cuts
- Easy to install
- Automatic on and off with saw blade rotation
- Extra long bolts included
Rating : 3.9
List Price : $43.34
0 comments:
Post a Comment